My Part Number:
Part Number: 750-632
Manufacturer Code: 750-632
Multiples of: 1 | Minimum Order: 1
Proportional valve module
The 750-632 Proportional Valve Module controls two single-coil valves with up to 24 V/1.6 A or one valve with up to 24 V/2 A. The module features two current-controlled PWM* outputs with adjustable dithering.
Both unipolar and bipolar valve control are possible. Additionally, operation of a valve with two unipolar coils is also provided. The module is single-channel in this operating mode! Characteristic curve adaptations, such as zero offset, dual gain compensation or range limitations, can be adjusted via parameters.
Scaling and configurable up/down ramps permit set point adjustment to the application. For example, monitoring threshold value switches is performed via two additional digital inputs. Start-up and valve parameters adjustment are performed via WAGO-I/O-CHECK software or the controller.
*PWM = Pulse width modulation
Number of digital inputs: 2
Number of outputs: 2 bipolar outputs (A+, A- and B+, B-)
Type of output: H-bridge output with current-regulated PWM output (short-circuit-proof and thermal overload-proof for each channel)
Input characteristic: high-side switching
Input characteristicl: Type 1
Input current (typ.): 2.7 mA at 24 V
Output current: 1-channel operation: 2 A; 2-channel operation: 1.6 A per channel
Load type: Operating range: inductive (1 mH … 600 mH); Internal load resistance (> 8 Ohm)
PWM frequency (typ.): 50kHz
Data width: 6 bytes: single-channel operating mode; 12 bytes: dual-channel operating mode
Supply voltage (system): 5 VDC; via data contacts
Current consumption (5 V system supply): 125mA
Supply voltage (field): 24 VDC (-25 … +30 %); via power jumper contacts (power supply via blade contact; transmission via spring contact)
Current consumption, field supply (module with no external load): 20mA
Isolation: 500 V system/field
Indicators: LED (1, 8, 9, 15) green: Signal Status DI 1, Undervoltage, Signal Status DI 2, Parameterization Status; LED (3, 5, 11, 13) yellow: Setpoint, Dithering Channel A, B; LED (4, 6) red/green: Status Channel A, B; LED (7, 16) red: Initialization, Error
Number of incoming power jumper contacts: 2
Number of outgoing power jumper contacts: 2
Brand |
WAGO |
|
£271.64
per 1 (ex. VAT)£325.97
per 1 (inc. VAT)
Proportional valve module
The 750-632 Proportional Valve Module controls two single-coil valves with up to 24 V/1.6 A or one valve with up to 24 V/2 A. The module features two current-controlled PWM* outputs with adjustable dithering.
Both unipolar and bipolar valve control are possible. Additionally, operation of a valve with two unipolar coils is also provided. The module is single-channel in this operating mode! Characteristic curve adaptations, such as zero offset, dual gain compensation or range limitations, can be adjusted via parameters.
Scaling and configurable up/down ramps permit set point adjustment to the application. For example, monitoring threshold value switches is performed via two additional digital inputs. Start-up and valve parameters adjustment are performed via WAGO-I/O-CHECK software or the controller.
*PWM = Pulse width modulation
Number of digital inputs: 2
Number of outputs: 2 bipolar outputs (A+, A- and B+, B-)
Type of output: H-bridge output with current-regulated PWM output (short-circuit-proof and thermal overload-proof for each channel)
Input characteristic: high-side switching
Input characteristicl: Type 1
Input current (typ.): 2.7 mA at 24 V
Output current: 1-channel operation: 2 A; 2-channel operation: 1.6 A per channel
Load type: Operating range: inductive (1 mH … 600 mH); Internal load resistance (> 8 Ohm)
PWM frequency (typ.): 50kHz
Data width: 6 bytes: single-channel operating mode; 12 bytes: dual-channel operating mode
Supply voltage (system): 5 VDC; via data contacts
Current consumption (5 V system supply): 125mA
Supply voltage (field): 24 VDC (-25 … +30 %); via power jumper contacts (power supply via blade contact; transmission via spring contact)
Current consumption, field supply (module with no external load): 20mA
Isolation: 500 V system/field
Indicators: LED (1, 8, 9, 15) green: Signal Status DI 1, Undervoltage, Signal Status DI 2, Parameterization Status; LED (3, 5, 11, 13) yellow: Setpoint, Dithering Channel A, B; LED (4, 6) red/green: Status Channel A, B; LED (7, 16) red: Initialization, Error
Number of incoming power jumper contacts: 2
Number of outgoing power jumper contacts: 2
Brand |
WAGO |
|
