My Part Number:
Part Number: 750-637/000-004
Manufacturer Code: 750-637/000-004
Multiples of: 1 | Minimum Order: 1
Incremental encoder interface - 24 VDC, Single-ended, 32 bits, Cam output
This module is an interface for any incremental encoder with standard connections.
A counter with a quadrature decoder as well as a latch for the zero impulse can be read or enabled by the controller. The module's control can set the counter. Depending on the operating mode, the counter value is added to the latch register on a positive edge at the “C” or “Latch” input. The rate (increments/ms) is automatically acquired and can also be transmitted to the controller as an alternative to the latch value. A counter lock-out is possible using the “Gate” input. Input “Ref“ can be used to activate the initial point “C“ function.
The cam outputs N1 and N2 indicate whether the counter value is within a defined range of values. The range can be adjusted.
The module must be powered using an external 24 VDC power supply, from which power to the transmitter (Ui, U0) can also be derived.
The shield directly connects to the DIN-rail.
Counter depth: 32Bit
Encoder connection: A; B; C (single-ended inputs)
Supply current (encoder) max.: 300mA
Zero impulse (latch): 32Bit
Quadrature decoder: 4x evaluation
Input current (typ.): Latch 5 mA, Gate 7 mA, Ref. 7 mA
Output current per channel: 0.5A
Output current: short-circuit-protected
Output voltage: 24 VDC
Voltage range for signal (0): −3 … +5 VDC
Voltage range for signal (1): 15 … 30 VDC
Data width: 1 x 32-bit data 2 x 8-bit control/status
Limit frequency: 250kHz
Commands: Reading, setting, activating
Supply voltage (system): 5 VDC; via data contacts
Current consumption (5 V system supply): 110mA
Current consumption, field supply (module with no external load): 35mA
Isolation: 500 V system/field
Indicators: LED (A-D/A-D) green: A, C, B, Latch, Gate, N1, Ref, N2
Brand |
WAGO |
|
£328.00
per 1 (ex. VAT)£393.60
per 1 (inc. VAT)
Incremental encoder interface - 24 VDC, Single-ended, 32 bits, Cam output
This module is an interface for any incremental encoder with standard connections.
A counter with a quadrature decoder as well as a latch for the zero impulse can be read or enabled by the controller. The module's control can set the counter. Depending on the operating mode, the counter value is added to the latch register on a positive edge at the “C” or “Latch” input. The rate (increments/ms) is automatically acquired and can also be transmitted to the controller as an alternative to the latch value. A counter lock-out is possible using the “Gate” input. Input “Ref“ can be used to activate the initial point “C“ function.
The cam outputs N1 and N2 indicate whether the counter value is within a defined range of values. The range can be adjusted.
The module must be powered using an external 24 VDC power supply, from which power to the transmitter (Ui, U0) can also be derived.
The shield directly connects to the DIN-rail.
Counter depth: 32Bit
Encoder connection: A; B; C (single-ended inputs)
Supply current (encoder) max.: 300mA
Zero impulse (latch): 32Bit
Quadrature decoder: 4x evaluation
Input current (typ.): Latch 5 mA, Gate 7 mA, Ref. 7 mA
Output current per channel: 0.5A
Output current: short-circuit-protected
Output voltage: 24 VDC
Voltage range for signal (0): −3 … +5 VDC
Voltage range for signal (1): 15 … 30 VDC
Data width: 1 x 32-bit data 2 x 8-bit control/status
Limit frequency: 250kHz
Commands: Reading, setting, activating
Supply voltage (system): 5 VDC; via data contacts
Current consumption (5 V system supply): 110mA
Current consumption, field supply (module with no external load): 35mA
Isolation: 500 V system/field
Indicators: LED (A-D/A-D) green: A, C, B, Latch, Gate, N1, Ref, N2
Brand |
WAGO |
|
